Setting up A Bathtub
Setting up A Bathtub
Blog Article
We've found this post on How to Install a Bathtub listed below on the web and felt it made sense to relate it with you on my blog.
Mounting a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently available, the job can move immediately; if you need to open a wall surface to remove the old bathtub and position the new bathtub, the job is a lot harder. In either situation, the task is within a home handyman's skills, although you will certainly need an assistant to move out the old tub and also set in the brand-new one. Make sure you have certified yourself for the task and also are comfortable trying it. As opposed to employing a specialist to take over a halfway-completed project, it is much better to take into consideration employing one prior to you start. Chances are you might require a professional plumber to make tube connections.
This post will certainly help you set up a brand-new bathtub in your shower room if you have actually currently bought a new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your tools as well as product list need to comprise the following:
Planning for the Installation
First of all, the sustaining frame supplied with the bathroom needs to be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets unit to prevent strain on the tub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final position.
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the restricted accessibility that is commonly the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a towel prepared for the continuing to be water that will originate from the pipelines. Once the supply pipelines have been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleansed of any old securing substance.
Before going on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Bath tub
Using both wooden boards under its feet, position the bathtub in the required placement. The wood boards are useful in equally spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 little factors.
The following goal is to guarantee that the tub is leveled all round. This can be achieved by checking the level as well as changing the feet on the bathtub until the level reviews degree.
To set up faucets, fit all-time low of the furthest flexible faucet connector to the ideal supply pipe by making a compression join; then do the exact same for the various other faucet.
Switch on the water supply and check all joints and new pipework for leaks as well as tighten them if needed. Fill up the tub and likewise inspect the overflow outlet as well as the typical outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the maker's instruction manual. Tiling and sealing around the tub must wait up until the bath tub has actually been made use of at the very least once as this will settle it into its final placement.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will require reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers are in location in between the faucet as well as the sink. Secure the tap in place with the maker supplied backnut. As soon as the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former type must be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to crack a stiff seal, triggering the water to permeate the wall between the bathroom as well as the tiling, bring about difficulties with dampness and feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and also cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly load the bath tub with water before sealing, to allow for the activity experienced when the bathtub is in usage. The sealer can split relatively early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a devoted person who reads about How to Install a Bathtub Yourself, I assumed sharing that excerpt was essential. Sharing is nice. You never know, you may very well be helping someone out. Many thanks for your time. Come back soon.
Schedule Free Estimate
Report this page